- ntg-context - NTG Mailing Lists

\frac broken in current beta
by Marco Patzer 16 Apr '13

16 Apr '13

Hi, \starttext \math{\frac12} \stoptext gives ! LuaTeX error [string "\directlua "]:1: attempt to call field 'math_frac' (a n il value) stack traceback: [string "\directlua "]:1: in main chunk. Marco

3 2

header variations how?
by Meer, H. van der 16 Apr '13

16 Apr '13

I tried to put the sectionnumbers in the margin, but it didn't work. The I looked at the example in the ConTeXt Reference Manual and this didn't work either. Why? See the minimal example below where the manual is contrasted with the actual output. Hans van der Meer \setuppapersize[A5][A5] \starttext \startchapter[title=Test] >From ConTeXt Reference Manual 18 october 2012 page 210\crlf \externalfigure[headers.jpg][width=0.8\textwidth] \startsection[title=enclosing section] \setupheads[alternative=normal] \subsection{Title alternative equals normal} \setupheads[alternative=inmargin] \subsection{Title alternative equals inmargin} \setupheads[alternative=middle] \subsubject{Title alternative equals middle} \stopsection ConTeXt ver: 2013.03.20 10:34 MKIV fmt: 2013.3.20 \stopchapter \stoptext

2 2

Re: [NTG-context] Overlapping \starthanging \stophanging with side captions
by Peter Sienkowski 15 Apr '13

15 Apr '13

Wolfgang, thank you very much for your answer about placing text. Using: \startplacefigure[location=force,title={First dummy caption}] \inmargin{First margin dummy} \externalfigure[dummy][width=\textwidth] \stopplacefigure The text in the \inmargin section appears at the bottom of the figure. This works for about one line of text. For some of the figures I'm trying to put 3-4 lines in a wide margin and would like the text to appear at the top or the middle of the figure. I asked a question over at Stackexchange on this: http://tex.stackexchange.com/questions/107856/placing-text-in-the-margin-ne… Using \starthanging \stophanging put the text in the correct place but then the figures ran into each other. regards Pete

1 0

Zoom to a box when clicking
by Aditya Mahajan 15 Apr '13

15 Apr '13

For a presentation, I want to display a series of images as a combination and be able to click on an image to zoom into that image and click again to zoom out. Is it possible to do that? In general, can I create a hyperlink such that clicking on it zooms in on a particular rectangular region on a page? Thanks, Aditya

4 7

options of \setupnotation and \setupnote
by Tim Li 15 Apr '13

15 Apr '13

Could you tell me what's the options of these two commands that haven't been updated on the wiki?

4 7

vskip in lines
by "H. Özoguz" 15 Apr '13

15 Apr '13

With \vskip-0.9cm one can relocate 0.9cm. If one uses grid-setting, it would be easier to give the dimension in lines, like \vskip-2*line – but this gives an error, how to do that correctly? Huseyin

3 2

tikz-cd - commutative diagrams
by Idris Samawi Hamid ادريس سماوي حامد 15 Apr '13

15 Apr '13

Dear gang, The tikz module works, as per the attached attached test file. I need some commutative diagrams and found something relatively recent and interesting: http://www.ctan.org/pkg/tikz-cd But \input'ing the file tikz-cd.tex after the tikz module does not work; I get an undefined control sequence for a normal tikz command. I commented the LaTeX commands % \ProvidesPackage{tikz-cd}[2012/12/30 v0.3c Commutative diagrams with tikz.] % \RequirePackage{tikz}[2010/10/13] % pgf version 2.10 required and the rest is just pgf syntax. What else do I need to do to get this working properly? Do I need to place tikz-cd in the pgf tree? If so, where? In the attached I have not used any code that depends on tikz-cd; comment \usemodule[tikz-cd] and the file runs fine. Thanks for any advice and Best wishes Idris -- Professor Idris Samawi Hamid Department of Philosophy Colorado State University Fort Collins, CO 80523

1 0

Vertical location of combinations
by Aditya Mahajan 15 Apr '13

15 Apr '13

How do I control the vertical location of combinations? I want output similar to ABC \framed[frame=no, location=top]}\startcombination[2] {\externalfigure[dummay][width=2cm]}{One} {\externalfigure[dummay][width=2cm]}{Two} \stopcombination} DEF without having to explictly add a \frame. Looking at pack-com, I tried \useMPlibrary[dum] \setupcombination[location=top] \starttext ABC \startcombination[2] {\externalfigure[dummay][width=2cm]}{One} {\externalfigure[dummay][width=2cm]}{Two} \stopcombination DEF ABC \framed[frame=no, location=top]}\startcombination[2] {\externalfigure[dummay][width=2cm]}{One} {\externalfigure[dummay][width=2cm]}{Two} \stopcombination} DEF \stoptext but the combination is still aligned to the baseline of the caption. Thanks, Aditya

2 2

Re: [NTG-context] Deactivating gridsetting for TOC
by "H. Özoguz" 15 Apr '13

15 Apr '13

Am 15.04.2013 19:03, schrieb ntg-context-request(a)ntg.nl: > Is there maybe another "trick" to deactivate gridsetting, analogical to > placeongrid, or tricks with tables, or so? I am experimenting here, too, > of course:) > > Huseyin Ok, maybe it is possible with a combination of \placeongrid and a command, which forces page-break of the toc on specified titles, or lines. Is there a pissibility to manually page-break the toc?

2 1

[***SPAM***] Re: Deactivating gridsetting for TOC
by "H. Özoguz" 15 Apr '13

15 Apr '13

> You can try to add > > \definelayout[<pagenumber>][grid=no] > > to your document where you replace <pagenumber> with the number of the page where your TOC starts. > > Wolfgang Thanks for this idea, but it does not work. The grid=no is simply ignored for the toc-page (as many grid=no options are ignored in many environments and commands, seems to be field open for improvements). Is there another idear for a workaround? At the moment I have only one option: resigning these different font sizes in the toc, which are defined manually absolutely (possible, but awkward) Is there maybe another "trick" to deactivate gridsetting, analogical to placeongrid, or tricks with tables, or so? I am experimenting here, too, of course :) Huseyin

1 0