- ntg-context - Mailing Lists

installing metauml in context
by Shiv Shankar Dayal 09 Jul '10

09 Jul '10

Hi, I am running ConTeXt mark IV. I need to use metauml for my work. However, I could not get it installed. Please help. The install file which comes with it does not work for context. -- Best regards, Shiv Shankar Dayal

5 10

m-barcodes error
by Michael Green 09 Jul '10

09 Jul '10

I can’t get the example in the m-barcodes module to work. I have no urgent need to print barcodes; I was just curious. I'm writing in case I found an easily corrected bug. The release notes from 2010.05.08 call this module mkiv only. But according to the log, the file m-pstricks.mkii is used. And that seems to be the proximate cause of the error. mjg ------------------------------------- ConTeXt ver: 2010.06.23 12:45 MKIV fmt: 2010.7.6 int: english/english ------------------------------------- command: context "barcode-test.tex" ------------------------------------- file: barcode-test.tex \usemodule[barcodes] \starttext % this is copied straight from m-barcodes.mkiv \startPSTRICKS \pspicture(-4mm,-1mm)(38mm,26mm) \psbarcode{9781860742712}{includetext guardwhitespace}{ean13}% \endpspicture \stopPSTRICKS \stoptext ------------------------------------- log before the error: systems : begin file barcode-test-pstricks-0001 at line 1 system : module pstric loaded (/context/tex/texmf-context/tex/context/base/m-pstricks.tex (/context/tex/texmf-context/tex/context/base/m-pstricks.mkii ! I can't find file `multido'. <argument> \input multido \relax \input pstricks \relax \input pst-plot \rel... \firstoftwoarguments #1#2->#1 l.47 ...s}{using indirect method; enable write18}}

3 4

Installing Context Minimals on Windows
by John Devereux 09 Jul '10

09 Jul '10

Hi, I normally use linux, but I now need to install context on Windows (7). Right now the minimals installation fails for me in various ways, depending on how I do it. Running the graphical installer I get two dialogs "update failed error code 1" and "make failed error code 1". Using the command line method I get a message about a vtable error when I try to run context. (It looked like the one mentioned in earlier postings, sorry I don't have the exact message now). I want just MKIV + extras (and intend to try TexWorks). Any hints appreciated. Thanks, -- John Devereux

2 2

Best version of ConTeXt
by Tom 09 Jul '10

09 Jul '10

What would be the best version of ConTeXt to recommend to a friend who writes novels on a PC running Windows? The person has no programming skills. He would probably require some assistance installing Tex-Live or whatever and would need a stable version because he couldn't manage frequent updates. Problems would far outweigh additional features for him. Tom Benjey 717-258-9733 voice 717-243-0074 fax Twitter: @TomBenjey

9 14

writetolist causes mystery blank
by Michael Murphy 08 Jul '10

08 Jul '10

Hi all, I'm having a but of a problem using writetolist. In principle, I want to insert something into the table of contents, but I don't want to disturb the flow of the text. Unfortunately, the following code seems to generate a blank at the top of the page: \showframe \showmakeup \starttext \writetolist[section]{}{}% \framed{This box has been pushed down} \stoptext I've also tried using a section command where the output has been set to empty: \showframe \showmakeup \setuphead[section][ before=, after=, command=\mydonothing] \def\mydonothing#1#2{} \starttext \section{}% \framed{This box has been pushed down} \stoptext but that also gets me a blank. Incidentally, the same thing happens with writebetweenlist, (except that this seems to sometimes push content onto a new page for some reason). Any ideas? -- Michael Murphy

2 2

OT: mailing list activity
by Alan BRASLAU 08 Jul '10

08 Jul '10

This is totally off-topic: but given the fairly strong Dutch implication in creating ConTeXt, it may not be surprising that traffic on the mailing list has slowed-down recently. Not to ruffle the feathers of everyone else on the mailing list, either... Alan

3 4

context vs texinfo
by Shiv Shankar Dayal 08 Jul '10

08 Jul '10

Hi, I was using context and I had to wait for 16 seconds for one run approximately. I switched to texinfo and it barely takes 2 seconds. Can you please explain the diffrence? I know context is complex but still? -- Best regards, Shiv Shankar Dayal

5 5

\definecolumnsethsize
by Richard Stephens 07 Jul '10

07 Jul '10

I'm using columnsets for a paper with 2 columns and copied an examples from the wiki and the columnsets documentation to give the following commands: \definecolumnset[colset][n=2] \setupcolumnset[colset][2][distance=5mm] \definecolumnsethsize{colset}{1}{1}\One \definecolumnsethsize{colset}{1}{2}\Two ... \placefigure[btlr][fig:ex1]{caption1}{\externalfigure[example1][width=\One]} % One column figure \placefigure[btlr][fig:ex2]{caption1}{\externalfigure[example2][width=\Two]} % Two column figure The figures appear okay, but they are quite a bit smaller than the textwidth of the columns. Can someone explain the workings of \definecolumnsethsize? I've looked at the code and it means nothing to me! The columnsets document only gives examples, no definition. Thanks verily, Richard Converteam UK Ltd. Registration Number: 5571739 and Converteam Ltd. Registration Number: 2416188 Registered in England and Wales. Registered office: Boughton Road, Rugby, Warwickshire, CV21 1BU. CONFIDENTIALITY : This e-mail and any attachments are confidential and may be privileged. If you are not a named recipient, please notify the sender immediately and do not disclose the contents to another person, use it for any purpose or store or copy the information in any medium. http://www.converteam.com Please consider the environment before printing this e-mail.

1 0

A problem with combining characters
by luigi scarso 07 Jul '10

07 Jul '10

In this example \N{COMBINING CARON BELOW} looks bad -- a font problem ? \usetypescript[libertine] \setupbodyfont[libertine,rm,10pt] \setupinterlinespace[line=2.6ex] \starttext %%echo '\N{LATIN SMALL LETTER A}\N{COMBINING DOT BELOW}\N{COMBINING CARON BELOW}' |./uconv -t utf-8 -x "name-any ạ̬ \stoptext -- luigi

2 6

underscore in index entry
by Shiv Shankar Dayal 07 Jul '10

07 Jul '10

Hi, I tried to put _ in index entry and am unable to do it. I tried following 1. \index{_shiv} 2. \index{\type{_shiv}} 3. \index{\textunderscore{} shiv} Please help. -- Best regards, Shiv Shankar Dayal

2 1